---
title: "Immersion heater tripping the electrics | 5.0 Star · From £50"
description: "Immersion heater tripping the electrics in Banstead? TMB Electrics tests the heater circuit and finds the fault before repair work. · Call 07460 070551"
canonical: "https://www.tmbelectrics.co.uk/problems/immersion-heater-tripping"
---

# Immersion heater tripping the electrics

> Immersion heater tripping the electrics in Banstead? TMB Electrics tests the heater circuit and finds the fault before repair work. · Call 07460 070551

An immersion heater that trips the electrics needs testing before it is used again. TMB Electrics checks the heater circuit and identifies whether the fault is in the element, thermostat, switch or supply.

## Why does an immersion heater trip the electrics?

An immersion heater can trip a circuit breaker or RCD when electricity leaks from the element or another part of the heater circuit develops a fault.
- **The heating element has failed:** The element is the part inside the cylinder that heats the water. A damaged element can allow electricity to leak to earth and make the RCD switch off.
- **The thermostat has a fault:** The thermostat controls the water temperature. A fault in the thermostat can stop the heater working properly or cause the circuit to trip when heating starts.
- **The immersion switch is damaged:** A worn switch, loose connection or heat damage at the isolator can interrupt the supply to the immersion heater. Testing identifies whether the switch is part of the fault.
- **The supply to the cylinder has a fault:** A damaged cable or failed connection on the circuit can trip the protective device when the immersion draws power. Testing follows the supply from the consumer unit to the cylinder.

## What can I check safely before booking?

You can note what happens when the heater comes on without opening the cylinder, removing covers or touching any electrical wiring.
- **Note what has tripped:** Check whether the circuit breaker or RCD has switched off. Note whether other sockets, lights or equipment have lost power at the same time.
- **Note when the fault happens:** Write down whether the trip happens as soon as the immersion is switched on, after a timer starts, or after the water has been heating for a while.
- **Look for visible heat damage:** Do not use a switch with scorch marks, cracking, smoke, unusual warmth or a burning smell. Leave the immersion circuit off if it is already off.

## When should I book an immersion heater repair?

Book an immersion heater repair when the circuit trips again, the hot water stays cold, or a switch or fitting shows signs of overheating.
- **The circuit trips when hot water starts:** A circuit that trips when the immersion heats needs testing. Repeated resetting can leave the fault connected to the installation.
- **The water is no longer heating:** Cold water at the taps can mean the element, thermostat, switch or supply has failed. Testing identifies which part has stopped the cylinder heating.
- **There is heat or scorching:** A burning smell, smoke, scorch marks or a hot immersion switch needs prompt attention. Stop using the affected circuit.

## What happens when an immersion heater is tripping?

The visit starts at the consumer unit and cylinder, then testing identifies whether the fault is in the heater or its electrical supply.
- **The heater circuit is identified:** The consumer unit, immersion switch and cylinder supply are checked to establish which protective device serves the heater.
- **The element and controls are tested:** The immersion element, thermostat, switch and supply are tested to narrow the fault to the part that has failed.
- **The repair work is explained:** The failed part is identified before repair work is priced. The cylinder is drained only when the failed part needs removing.

## What does immersion heater fault finding cover?

The price covers the time needed to test the immersion heater circuit, element, thermostat and switch, then identify why the electrics are tripping. The price changes when testing finds a failed part, damaged connection or repair that needs replacement parts.
- Fault finding & repair: from £80 an hour
- Testing covers the electrical supply to the cylinder and the parts that control the immersion heater.
- Replacement elements, thermostats, switches and seals change the price when they are needed.
- Work on the cylinder, water system or gas heating is not included in immersion heater electrical repair.

## Immersion heater tripping questions

### Can a faulty immersion heater trip an RCD?

Yes. A failed immersion element can leak electricity to earth and make an RCD switch off. Testing identifies whether the trip comes from the element, thermostat, switch or supply.

### Should I keep resetting the immersion heater circuit?

No. If the circuit trips again, leave it off until the cause has been tested. Repeated resetting can leave a fault connected to the installation.

### Why does my immersion heater trip only when the timer starts?

The timer may be bringing the immersion heater into use at that time. The fault can be in the heating element, thermostat, switch or circuit that becomes live when the timer operates.

### Can an immersion heater be repaired without replacing the cylinder?

Yes, when the fault is in the element, thermostat, switch or electrical supply to the existing cylinder. Testing identifies the failed part before any repair work is priced.

## Related problems
- [Burning plastic smell from electrics](https://www.tmbelectrics.co.uk/problems/burning-plastic-smell-electrical): A burning plastic smell needs the affected electrical circuit checked before it is used again.
- [Circuit breaker keeps tripping](https://www.tmbelectrics.co.uk/problems/circuit-breaker-keeps-tripping): A repeated trip usually means a circuit, fitting or connected item needs testing.
- [Circuit breaker will not reset](https://www.tmbelectrics.co.uk/problems/circuit-breaker-wont-reset): A circuit breaker that stays off needs the affected circuit checked for a fault.
- [Consumer unit is hot](https://www.tmbelectrics.co.uk/problems/consumer-unit-hot): A hot consumer unit can point to an overloaded circuit or failing connection that needs testing.
- [Consumer unit tripping with nothing plugged in](https://www.tmbelectrics.co.uk/problems/consumer-unit-tripping-nothing-plugged-in): A trip with nothing plugged in usually needs the fixed circuit traced and tested.
- [Cooker tripping the electrics](https://www.tmbelectrics.co.uk/problems/cooker-tripping-electrics): A cooker trip can come from its circuit, connection or the appliance itself.

## Sources
- [BS 7671: IET Wiring Regulations](https://electrical.theiet.org/bs-7671/)
- [Electrical Safety First: Safety Guidance](https://www.electricalsafetyfirst.org.uk/guidance/)
- [Energy Saving Trust: Heating Your Home](https://energysavingtrust.org.uk/advice/heating-your-home/)

Updated 2026-11-19.

[Electrical fault finding](https://www.tmbelectrics.co.uk/services/electrical-fault-finding)

## Book or ask a question
- [Book Now](https://www.tmbelectrics.co.uk/#chat)
