---
title: "Kitchen under cabinet lights not working | 5.0 Star · From £50"
description: "Kitchen under cabinet lights not working in Banstead? TMB Electrics tests the driver, switch and supply to find the fault and explains the repair."
canonical: "https://www.tmbelectrics.co.uk/problems/kitchen-under-cabinet-lights-not-working"
---

# Kitchen under cabinet lights not working

> Kitchen under cabinet lights not working in Banstead? TMB Electrics tests the driver, switch and supply to find the fault and explains the repair.

Dead kitchen under cabinet lights point to the small driver box that feeds them, or the switch and breaker ahead of it. TMB Electrics in Banstead tests the supply and the driver to find which has failed.

## Why have my kitchen under cabinet lights stopped working?

Under cabinet lights run on low voltage, so a small box called a driver steps the mains power down for them. What stopped tells you where to look.
- **The driver has failed:** The driver is the small box that turns mains power into low voltage for the light strip or spotlights. When it fails, every light on it goes dark together.
- **The supply to the driver has been lost:** A tripped kitchen lighting breaker, a switched off isolator or a faulty wall switch cuts the power before it reaches the driver, so the whole run goes out as one.
- **One lamp has failed:** When a single light is dead and the rest work, the fault sits with that lamp or its connector, not with the driver.
- **The lamps and the dimmer do not suit each other:** A lamp that is not made for dimming flickers or cuts out on a dimmer switch. Replacement lamps must match the fitting and the driver rating.
- **A connector has worked loose or corroded:** A poor connection between the driver and a light leaves it dead or cutting out, and a loose connection runs hot inside the cupboard.

## What can I check safely before calling an electrician?

These checks need no tools and nothing is opened. Leave the lights off and stop if anything smells of burning or feels hot.
- **Count how many lights are dead:** Note whether one light or the whole run is out. A whole run points to the driver or its supply, while one dead light points to that lamp.
- **Try the wall switch and the dimmer:** Flick the switch off and on, and turn any dimmer fully up. Note whether anything changes, since a worn switch can cut the supply to the driver.
- **Look at the kitchen lighting breaker:** Look at the consumer unit and see whether the lighting breaker has dropped. Switch it back on once. If it drops again, leave it off and book a visit.
- **Look for heat marks:** Look at the lights, their cable and the cupboard around the driver for scorching or brown marks, without opening anything. Heat marks mean the lights stay off until they are checked.

## When should I book an electrician?

Book when the whole run stays dead after the switch and breaker check, or when anything shows signs of heat.
- **The whole run stays dead:** The switch works and the breaker is on, yet no light comes on. The driver and the wiring feeding it need testing with meters.
- **A light or driver shows heat:** Scorch marks, a hot cupboard or a burning smell mean switching the lights off at the consumer unit and booking a visit.
- **The lights flicker or cut out:** Flicker on a dimmer or lights that drop out point to a lamp and dimmer mismatch or a loose connection. Both need testing.
- **The lights failed after new work:** Lights that stopped after a new appliance, unit or fitting went in need a check of what was disturbed during that work.

## What happens on the visit?

The visit follows the power from the wall switch to the last light, then ends with the lighting tested and switched on.
- **We ask what happened first:** We ask which lights are out, when it began and what changed beforehand, then look at the switch, the dimmer and the breaker.
- **The supply and the driver are tested:** With the circuit isolated, we test for power at the switch, then at the driver input and the driver output. That shows whether the driver or its supply has failed.
- **The failed part is replaced:** A failed driver is replaced with one matched to the voltage and total wattage of the lights. Loose connectors are remade and damaged fittings are swapped.
- **The lighting is tested and handed back:** The circuit is tested and the lights are switched on from the wall so you see them work. Anything bigger is explained and priced separately.

## What does the fault finding price cover?

Fault finding is charged by the hour for the time spent testing the lighting circuit and finding the failed part. A replacement driver, lamps or any other repair is priced once the cause is known.
- Fault finding & repair: from £80 an hour
- A driver or transformer is a part, so it is added to the labour once testing shows it has failed.
- A fault at the switch or the breaker is traced within the same testing, before any part is chosen.
- Repairs to the light fittings themselves, or new lighting, are quoted separately.

## Under cabinet lighting questions

### Why have all my kitchen under cabinet lights stopped at once?

The driver feeding them has failed, or its supply has been lost at the switch or the consumer unit. We test the supply and the driver to find which.

### Can I fit any replacement LED in my under cabinet lights?

No. A replacement lamp must match the fitting and the driver, and its stated rating must not be exceeded. Check the markings, or ask us to match the right lamp.

### Why do my under cabinet lights flicker on the dimmer?

A lamp that is not made for dimming misbehaves on a dimmer switch. Lamps that cannot be dimmed carry a symbol saying so. We test the lamps and the dimmer together to find the mismatch.

### How is the cost of fixing under cabinet lights worked out?

Fault finding is charged by the hour while the cause is found. The repair is priced once the cause is known, with any driver or parts added to the labour.

## Related problems
- [Burning plastic smell from electrics](https://www.tmbelectrics.co.uk/problems/burning-plastic-smell-electrical): A burning plastic smell needs the affected electrical circuit checked before it is used again.
- [Circuit breaker keeps tripping](https://www.tmbelectrics.co.uk/problems/circuit-breaker-keeps-tripping): A repeated trip usually means a circuit, fitting or connected item needs testing.
- [Circuit breaker will not reset](https://www.tmbelectrics.co.uk/problems/circuit-breaker-wont-reset): A circuit breaker that stays off needs the affected circuit checked for a fault.
- [Consumer unit is hot](https://www.tmbelectrics.co.uk/problems/consumer-unit-hot): A hot consumer unit can point to an overloaded circuit or failing connection that needs testing.
- [Consumer unit tripping with nothing plugged in](https://www.tmbelectrics.co.uk/problems/consumer-unit-tripping-nothing-plugged-in): A trip with nothing plugged in usually needs the fixed circuit traced and tested.
- [Cooker tripping the electrics](https://www.tmbelectrics.co.uk/problems/cooker-tripping-electrics): A cooker trip can come from its circuit, connection or the appliance itself.

## Sources
- [Electrical Safety First: downlights](https://www.electricalsafetyfirst.org.uk/guidance/safety-around-the-home/downlights/)
- [Electrical Safety First: safe installation of retrofit LED lamps (Best Practice Guide 9)](https://www.electricalsafetyfirst.org.uk/media/pqkn2dgz/best-practice-guide-9.pdf)
- [Electrical safety questions answered](https://www.electricalsafetyfirst.org.uk/safety-advice/your-questions-answered/)

Updated 2026-11-20.

[Electrical fault finding](https://www.tmbelectrics.co.uk/services/electrical-fault-finding)

## Book or ask a question
- [Book Now](https://www.tmbelectrics.co.uk/#chat)
