Electric shower tripping the electrics
An electric shower that trips the electrics needs its circuit checked before use. TMB Electrics traces the cause in Banstead and identifies the work needed to leave the shower circuit safe.
Calls answered 24/7
- 14 years trading
- Local to Banstead
- Clear, upfront quotes
Why does my electric shower trip the electrics?
An electric shower draws a large electrical load, so a fault in the shower or its dedicated circuit can operate the protective device at the consumer unit.
- The shower has developed a faultA fault inside the shower can cause the circuit to trip when the unit starts heating. The shower is tested separately from the fixed circuit to identify where the fault sits.
- The circuit protection has detected a faultAn RCD is a safety switch that cuts power when electricity flows where it should not. A trip can come from the shower, its cable, the isolator, or another part of the circuit.
- A connection has overheated or failedA loose connection at the isolator, shower supply or consumer unit can create heat and cause the circuit to trip. Testing identifies the affected connection before it is used again.
- The shower rating does not match the circuitA replacement shower can draw more current than the previous unit. The cable, protective device and isolator must match the rating of the shower connected to them.
What can I check safely before booking?
You can note the pattern and look for visible signs without opening the shower, removing covers, or touching any mains wiring.
- Note when the trip happensRecord whether the trip happens when the shower starts, when it heats water, or after it has run for a while. Note whether other rooms or circuits lose power too.
- Look for visible damageDo not use the shower if you notice scorching, cracking, smoke, a burning smell, or unusual warmth around the pull cord, isolator or shower unit.
- Leave the circuit off after a repeat tripIf the shower circuit trips again, leave it off where you can do so safely at the consumer unit. Do not keep restoring power to a circuit that will not stay on.
When should I book electrical fault finding?
Book Electrical Fault Finding & Repair when the shower circuit trips again, the cause is unclear, or any part of the installation shows signs of heat damage.
- The shower trips as it starts or heatsA repeated trip when the shower is used needs testing of the shower and its dedicated circuit. The cause may be in the unit, cable, isolator or protective device.
- The circuit will not stay onA circuit that trips again after it is restored needs investigation. Leaving it unused prevents the shower from being run with a fault still connected.
- There is heat, smoke or scorchingA burning smell, smoke, scorch marks or a hot electrical fitting needs prompt attention. Stop using the shower and leave the affected circuit off.
What happens when an electric shower trips the electrics?
The visit follows the shower circuit from the consumer unit to the shower, using testing to separate a shower fault from a fixed wiring fault.
- The shower circuit is identifiedThe consumer unit, protective device, isolator and shower supply are checked to confirm which circuit feeds the shower and what else it affects.
- The circuit and shower are testedTesting checks the fixed cable, connections and protective devices, then separates those results from the shower unit where needed.
- The cause is explainedThe failed part or remaining investigation is explained once testing identifies it. Any repair or replacement work is set out before it begins.
What does electric shower fault finding cover?
The price covers the time needed to investigate why the electric shower trips the electrics, including testing the shower circuit, protective device, isolator and relevant connections. The price changes if testing identifies a failed shower, damaged cable, faulty protective device, heat damage, replacement parts or repair work beyond the investigation.
From £80 an hour
Included when agreed
- Testing the affected circuit and the fuse board
- Tracing the fault to the socket, fitting, cable or appliance
- Repairs that can be done on the spot with parts carried
- A clear explanation of what was wrong
Not included automatically
- New circuits or upgrades the fault reveals, which are quoted separately
- Repairs to the appliance itself
Ways to pay


- Pay by bank
- Bank transfer
- Testing covers the shower circuit and the electrical parts connected to the reported trip.
- Repair work and replacement parts are priced once the cause is known.
- A fault inside the shower unit may need shower repair or replacement after the electrical tests.
How booking works
Tell us about the job
Tap Book Now and describe the work in the chat. Photos help.
Get your price
You see your price in the chat. A set price is paid at checkout; any other job is quoted first.
Choose your visit
Give your address and when you are free, and the visit is arranged.
Why choose TMB Electrics
- Reviews
- 39
- Rating
- 5.0
- Trading since
- 2012
“I keep things straightforward: you deal with me from the first quote to the final check, with clear advice and no surprises along the way.”
Trevor Bush, TMB Electrics
Book NowWhy does my electric shower trip the RCD?
The RCD has detected electricity flowing where it should not. The cause can be inside the shower, at the isolator, in the cable, or at another connection on the shower circuit. Testing identifies which part is responsible.
Can I reset the breaker and keep using the shower?
No. If the breaker or RCD trips again when the shower is used, leave the circuit off and stop using the shower. Repeated resetting can leave a fault connected to the installation.
Can a more powerful shower make the circuit trip?
Yes. A shower with a higher rating can overload a circuit that was suitable for an older unit. The cable, protective device and isolator need checking against the rating before a replacement shower is connected.
Is the fault always inside the shower?
No. The shower is one possible cause, but the fault can also be in the fixed circuit, isolator, cable or consumer unit. Testing separates the shower from the installation before repair work is planned.
Related problems
- Burning plastic smell from electricsA burning plastic smell needs the affected electrical circuit checked before it is used again.
- Circuit breaker keeps trippingA repeated trip usually means a circuit, fitting or connected item needs testing.
- Circuit breaker will not resetA circuit breaker that stays off needs the affected circuit checked for a fault.
- Consumer unit is hotA hot consumer unit can point to an overloaded circuit or failing connection that needs testing.
- Consumer unit tripping with nothing plugged inA trip with nothing plugged in usually needs the fixed circuit traced and tested.
- Cooker tripping the electricsA cooker trip can come from its circuit, connection or the appliance itself.
Sources
- BS 7671: IET Wiring Regulations
- Electrical Safety First: Bathroom electrical safety
- HSE: Electrical safety
Updated 19 November 2026
