Electrics trip when I plug something in
Electrics trip on plugging in when the appliance, its lead, the socket or the circuit leaks current or overloads. TMB Electrics tests each in Banstead and names the failed part before repairing it.
Calls answered 24/7
- 14 years trading
- Local to Banstead
- Clear, upfront quotes
Why do my electrics trip when I plug something in?
The protective device on that circuit cuts the power the moment a plug adds a fault, or a load the circuit cannot carry. Five causes cover most cases.
- An appliance leaking to earthWorn insulation inside a kettle, heater or washing machine lets current reach its metal casing. A residual current device, or RCD, is the safety trip in the consumer unit that cuts power in a fraction of a second when that happens.
- A damaged plug or leadA crushed lead, a loose wire inside the plug or bent pins can bring the live and neutral wires together as the plug goes in. The trip drops at once, sometimes with a spark or bang at the socket.
- A surge as the appliance startsMotors in drills, hoovers and compressors pull a brief rush of current when they start, called inrush. A sensitive breaker can read that rush as a fault even when the appliance itself is sound.
- Too much load on the circuitA breaker trips when the total draw passes its rating. A heater and a kettle on the same sockets leave little spare, so one more plug can tip the circuit over.
- A worn or damp socketSlack terminals behind the faceplate, scorched pin holes or damp in a kitchen or outdoor socket can fault as soon as a plug goes in. Appliances that run happily elsewhere then trip only at that socket.
What can I safely check at home?
These checks need only the appliance, its plug and a look at the fuse board cover. Nothing gets opened, unscrewed or touched inside.
- Try the appliance in another roomPlug it into a socket on a different circuit. If it trips there too, the fault travels with the appliance and its cable. If it runs, the first socket or its circuit needs testing. Unplug it again afterwards.
- Read the fuse board through its coverNote which trip dropped without removing anything. A wide switch marked T or with a test button is an RCD, and a narrow one is a breaker. Reset it once only, and only if the board is cool and smells normal.
- Inspect the plug and lead by eyeWith the appliance unplugged, check the pins for browning, the plug body for cracks and the lead for kinks, cuts or exposed wire. Keep anything damaged unplugged and out of use.
- Watch for warning signs at the socketA buzz, a warm faceplate or brown marks around the pin holes point to a loose connection behind it. Stop using that socket and leave its circuit switched off at the board.
When should I book an electrician?
Book when the trip keeps coming back, when ordinary plugs set it off, or when a socket gives off heat, a smell or a spark.
- Harmless items trip the same socketWhen a phone charger trips the power at one socket, the fault sits in that socket or the cable behind it. Leave it unused until it has been tested, then Book Now.
- The trip will not stay resetA switch that drops again with everything unplugged points to the circuit itself or the device guarding it. Leave it off and Book Now.
- A socket is hot, smells or sparksThese signs mean a connection is overheating. Switch that circuit off at the board, keep clear of the socket and Book Now.
What happens on the visit?
The visit starts with the appliance and the trip that dropped, then works back along the circuit before any part is changed.
- Questions and a look at the boardWe ask what you plugged in, when it began and which rooms lost power, then note which trip dropped. The cover stays on until a tester shows the circuit is dead.
- Testing with the circuit offThe tripped circuit is isolated, and the appliance, its lead and the socket wiring are tested separately. Insulation readings show whether current escapes between conductors or to earth.
- Naming the failed partYou hear which part failed before anything is fitted. A worn socket, faceplate or breaker can be swapped on the spot from the common parts we carry.
- Leaving the circuit testedAfter a repair the circuit is tested again and switched back on. A circuit that still fails stays off while the others keep running, and bigger work gets a written price.
How is the fault finding price worked out?
Fault finding is charged by the hour, so the price covers the time spent testing the appliance, socket and circuit, and explaining what we found. It changes with how long the fault takes to isolate, whether a part has to be fitted, and whether the repair alters the circuit.
From £80 an hour
Included when agreed
- Testing the affected circuit and the fuse board
- Tracing the fault to the socket, fitting, cable or appliance
- Repairs that can be done on the spot with parts carried
- A clear explanation of what was wrong
Not included automatically
- New circuits or upgrades the fault reveals, which are quoted separately
- Repairs to the appliance itself
Ways to pay


- Pay by bank
- Bank transfer
- A fault that appears only under load takes longer to pin down than one that trips the moment a plug goes in.
- Parts, a larger repair or a new circuit are priced once the cause is known, and you say yes before that work starts.
- Mending the appliance itself is not part of the visit, and a certificate for an altered circuit is priced when it is needed.
How booking works
Tell us about the job
Tap Book Now and describe the work in the chat. Photos help.
Get your price
You see your price in the chat. A set price is paid at checkout; any other job is quoted first.
Choose your visit
Give your address and when you are free, and the visit is arranged.
Why choose TMB Electrics
- Reviews
- 39
- Rating
- 5.0
- Trading since
- 2012
“I keep things straightforward: you deal with me from the first quote to the final check, with clear advice and no surprises along the way.”
Trevor Bush, TMB Electrics
Book NowIs it my appliance or my wiring?
Plugging the appliance into a socket in another room is the quickest sign. If it trips there too, the appliance is at fault. If it runs, the first socket or its circuit needs testing.
Should I keep resetting the trip?
Once is enough, and only while the board is cool and smells normal. If it drops again, leave it off and book a test. Repeated resets stress the breaker and any damaged cable.
Can a brand new appliance trip my electrics?
Yes. A fresh fault, damage in transit or a heavy start up surge can do it. Return a faulty new item under its warranty, and have the socket tested if other items trip there too.
Will the whole house lose power during the test?
Normally only the circuit being tested goes off. We say which rooms will lose power before we switch anything.
Do you repair the appliance itself?
No. TMB Electrics works on the socket, the circuit and the fittings, and names the appliance when it is the cause. Its repair or replacement is a job for the maker or a repairer.
Related problems
- Burning plastic smell from electricsA burning plastic smell needs the affected electrical circuit checked before it is used again.
- Circuit breaker keeps trippingA repeated trip usually means a circuit, fitting or connected item needs testing.
- Circuit breaker will not resetA circuit breaker that stays off needs the affected circuit checked for a fault.
- Consumer unit is hotA hot consumer unit can point to an overloaded circuit or failing connection that needs testing.
- Consumer unit tripping with nothing plugged inA trip with nothing plugged in usually needs the fixed circuit traced and tested.
- Cooker tripping the electricsA cooker trip can come from its circuit, connection or the appliance itself.
Sources
- Electrical Safety First: Safety Guidance
- BS 7671: IET Wiring Regulations (18th Edition)
- NICEIC: Householder Guidance
Updated 20 November 2026
