Immersion heater not working

TMB Electrics tests an immersion heater in Banstead to identify whether the element, thermostat, switch or electrical supply has stopped the cylinder heating.

Calls answered 24/7

  • 14 years trading
  • Local to Banstead
  • Clear, upfront quotes

Why is my immersion heater not heating water?

An immersion heater stops heating when its element, thermostat, switch or electrical supply has developed a fault.

  • The heating element has failedThe element is the part inside the cylinder that heats the water. A failed element can leave the cylinder cold even when its controls appear to be on.
  • The thermostat has stopped switchingThe thermostat controls the water temperature and switches the element on and off. A fault here can prevent the element receiving power or stop heating too soon.
  • The isolator or switch has a faultThe isolator is the switch that disconnects power to the immersion heater. A damaged switch or connection can stop electricity reaching the cylinder.
  • The electrical supply has trippedA circuit breaker or RCD can switch off when it detects an electrical fault. The immersion heater then cannot heat until the affected circuit has been checked.

What can I check safely before booking?

You can check the controls and note what has changed without removing covers, opening the cylinder or touching electrical wiring.

  • Check the timer settingCheck whether the hot water timer is set to heat at the time you expect. Note whether the cylinder has stopped heating at every programmed period or only at one.
  • Check the immersion switchLook at the immersion switch without removing its cover. Do not use it if it has scorch marks, cracking, smoke, unusual warmth or a burning smell.
  • Note what happens at the consumer unitNote whether a breaker or RCD has switched off and whether it stays on. Do not keep resetting a protective device that switches off again.

When should I book immersion heater repair?

Book immersion heater repair when the cylinder remains cold, its circuit will not stay on, or the switch shows signs of damage.

  • The water stays coldCold water after the timer should have heated can mean the element, thermostat, switch or supply needs testing.
  • The circuit switches off againA breaker or RCD that switches off again when the immersion is used needs investigation. Leave the affected circuit off where possible.
  • The switch looks damagedScorching, cracking, smoke, a burning smell or heat at the switch needs the immersion left unused until it has been checked.

What happens during an immersion heater repair visit?

The visit starts by testing the electrical supply at the cylinder, then identifies the failed part before any replacement work begins.

  • The supply is isolated and testedPower to the immersion heater is isolated before the element, thermostat, isolator and supply at the cylinder are tested.
  • The failed part is identifiedTesting shows whether the fault is in the element, thermostat, switch or supply. The required repair is explained before a replacement part is fitted.
  • The repair is checkedAfter the electrical work, the immersion supply and repaired part are tested to confirm the cylinder can heat safely.

What does immersion heater repair cover?

The price covers electrical testing at the cylinder and the labour needed to repair the identified fault. It changes with the failed part, the time needed for the repair, and whether the cylinder must be drained before an element or seal is replaced.

From £80 an hour

Included when agreed

  • Testing the affected circuit and the fuse board
  • Tracing the fault to the socket, fitting, cable or appliance
  • Repairs that can be done on the spot with parts carried
  • A clear explanation of what was wrong

Not included automatically

  • New circuits or upgrades the fault reveals, which are quoted separately
  • Repairs to the appliance itself

Ways to pay

  • Visa
  • Mastercard
  • American Express
  • Apple Pay
  • Google Pay
  • Pay by bank
  • Bank transfer
  • Testing covers the immersion element, thermostat, isolator and electrical supply at the cylinder.
  • Replacement elements, thermostats, switches and seals change the total when they are needed.
  • Written hours and fitted parts show what the repair involved.

View the fault finding cost guide

How booking works

  1. Tell us about the job

    Tap Book Now and describe the work in the chat. Photos help.

  2. Get your price

    You see your price in the chat. A set price is paid at checkout; any other job is quoted first.

  3. Choose your visit

    Give your address and when you are free, and the visit is arranged.

Why choose TMB Electrics

Photo of Trevor BushTrevor BushElectrician
Reviews
39
Rating
5.0
Trading since
2012
“I keep things straightforward: you deal with me from the first quote to the final check, with clear advice and no surprises along the way.”

Trevor Bush, TMB Electrics

Book Now

Immersion heater repair questions

Still have a question?

Can an immersion heater be repaired?

Yes, when testing identifies a fault in the element, thermostat, switch or electrical supply. The failed electrical part is identified before a replacement is fitted.

Why is my immersion heater tripping the electrics?

A fault in the element, thermostat, switch or supply can cause a breaker or RCD to switch off. Leave the circuit unused if it switches off again, then arrange testing.

Will the water be turned off during the repair?

The cylinder may need draining when an element or seal has to be removed. The work begins by testing the electrical parts at the cylinder to establish what is required.

What should I tell the electrician before the visit?

Say whether the water is always cold or only cold at certain times. Include the timer setting, any tripping at the consumer unit, and visible damage or heat at the immersion switch.

Related problems

Sources

Updated 19 November 2026

Book or ask a question

Calls answered 24/7